Primed bar

OS

Primed bar
Detailed
Release	2 October 2006 (Update)
Members	Yes
Members	Yes
Quest item	Elemental Workshop II, III, IV
Quest item	Elemental Workshop II, III, IV
Tradeable	No
Tradeable	No
Equipable	No
Equipable	No
Stackable	No
Stackable	No
Disassembly	Yes
Disassembly	Yes
Value	1 coin
Value	1 coin
High Alchemy	0 coins
High Alchemy	0 coins
Low Alchemy	0 coins
Low Alchemy	0 coins
Destroy	Drop
On death	Reclaimable
On death	Reclaimable
Reclaim	1
Reclaim	1
Sacrifice	4
Sacrifice	4
Exchange	Not sold
Weight	1.814 kg
Examine	A primed elemental ingot.

A primed bar is a bar of elemental metal that has undergone several processes making it receptive to the magical forces of the machines on the lower levels of the Elemental Workshop dungeon. Primed bars can be used in the dungeon to make mind, body, cosmic, and chaos bars.

Fabrication

Primed bars may be made by processing an elemental bar in the second basement level of the elemental workshop. There are two levers that operate the claw; the west one lowers and raises the claw while the east one rotates it 180 degrees.

Dunking the bar into the lava

Operate ("pull") the east lever at the southern part of the room to rotate the crane & claw. Position the crane & claw over the jig cart.

Place the elemental bar on the jig cart underneath the purple claw by "use elemental bar-> jig cart".

Operate the south-west lever 2x, the one right in front of the purple claw to lower the purple claw and pick up the elemental bar.

Operate the south-east lever to rotate the crane so that the purple claw and your elemental bar are over the molten lava.

Operate the south-west lever to dip the elemental bar into the lava.

Operate the south-west lever again to pull the elemental bar out of the lava.

Operate the south-east lever to bring the purple claw and the golden, hot elemental bar back around & to being above the jig cart.

Operate the south-west lever to drop the elemental bar back onto the jig cart.

Operate the south-west lever again to raise the purple claw.

Move the jig cart to the press

• Pull the north lever in the middle of the room (the jig cart operating lever) that is just underneath the yellow sign. Send the jig cart & the elemental bar to the next station.
• Pull north-western lever, that is directly next to the press (right clicking on it yields "An old lever") on the west side next to the 3 pipes which disappear into the floor of the room to flatten the elemental bar.

Move the jig cart to the water tank

• Pull the lever in the middle of the room (the jig cart operating lever) that is just underneath the yellow sign with the cart symbol on it.
• The cart stops in front of a water tank.

Submerging the bar in the water

• The flattened bar must be submerged in order to cool it. There are 4 controls.
  • "An old lever" - opens and closes the door to the tank next to where the flattened bar has stopped.
  • The "Corkscrew lever" - extends and retracts a track that moves the jig into and out of the cooling chamber.
  • A "Water valve" to the west and east - respectively, the west one turns the flow of water on and off, and the east one opens and closes the drain.
• If there is any water in the chamber, make sure the west valve is closed, then open and close the east valve.
• Pull the lever to open the door.
• Turn the corkscrew lever twice to pick up the flattened bar with the jig cart and move them into the water tank.
• Pull the lever to close the door.
• Open and close the valve to the west to flood the chamber.
• Open and close the valve to the east to drain the chamber.
• Pull the lever to open the door.
• Turn the corkscrew lever twice to move flattened bar with the jig cart back to the conveyor.
• Pull the lever to close the door.

The final station

• Pull the jig cart operator lever until the bar reaches the fan station.
• Pull the lever adjacent to the last station to start the fan. The messages; "The fan starts to blow" then "The machine starts rumbling" should pop up.
• Click through the messages telling you that the machine turns on, and then pull the lever once more to turn off the fan.
• Once the fan rumbles to a halt, pull the jig cart operating lever in the centre of the room. This brings the jig cart and the white bar back to the start. Retrieve the finished primed bar by selecting "take from the jig cart". Congratulations, you are successful!

Assuming one starts with ideal conditions (the tank is empty and the left and right valves are both closed) and you pull the lever for the cooling tank while waiting for the cart to go to the press and then turn the fan on and off while the cart is moving to the fan, it then takes approximately 2 minutes and 5 seconds to turn one elemental bar into a primed bar, if you do it station for station waiting for the cart which takes approximately 2 minutes and 15 seconds.

Disassembly

Disassembly XP	0.1
Item quantity required	1
Material count	1
Base junk chance	?  98.9% Your actual junk chance depends on your junk chance reduction researched. See the table below for all values, and Junk for more information. Reduction Junk chance None 1 98.9% 1 34 98.0% 2 49 96.0% 3 64 94.0% 4 69 92.0% 5 78 90.0% 6 83 87.1% 7 91 85.1% 8 95 82.1% 9 105 79.2%
Possible materials
Often
Simple parts	99%
Rarely
Variable components	1%

Defined properties:

All Junk chance: 98.9 Junk chance: 98.9

[FAQ] • [doc]

Trivia

• The creation of the primed bar requires all the four elements. An elemental bar is dipped in lava (fire), flattened by a press (earth), submerged in water (water) and is then cooled and dried using a giant fan (air).